"BC" Official Mods and Paint Thread. UPDATED 3/8/13 PGM restore and strip!

GM phase 2. http://i1296.photobucket.com/albums/ag2/Bcmaddog/8F9A9520-27F5-40B2-A7BD-5803E3C3DCA2-8344-00000557C4ABB842_zpsac2b131f.jpghttp://i1296.photobucket.com/albums/ag2/Bcmaddog/3DDF7A37-144D-497D-874D-CEEF971ECAC3-8344-00000557BFB8DB55_zpsd57896ca.jpg

Going to put these in some mineral spirits. Strip all the paint, add fresh silicone, and clean the spacers and bearing seat. Ect. Since I used sandpaper to strip what is gone currently, it smoothed it out. So I sanded it smoothed it and stripped some of it all at the same time :).

Grind Machine Restore Phase 2!

What kind of paint is it? Mineral spirits may not work. Then again any other solvent will probably eat the plastic.

If it’s just acrylic paint, use germ-x hand sanitizer, I’m not joking, removes the paint without damaging the plastic.

It was just a bottle of spray paint and a clear coat of spray paint.
I did this on some others because I wanted to paint more :).

I’m actually using Gum Spirits, will that eat the plastic? It is paint thinner. I used it on my one and it didn’t do anything, but I didn’t soak the ONE I just got a paper towel and touched it while spinning on a drill.

No, that probably won’t affect the plastic. Don’t know that I’d leave it soak though.

Well how am I going to get off?

I’m getting good :slight_smile:

How did you get it this far?

Sandpaper and a sandpaper block. But for some reason i cant get more off. And if i keep using sandpaper i might scrape to much of the plastic off. Its nice and smooth now. And i cant get inside where the hubstacks go.

Then maybe some mineral spirits and fine steel wool, or a green 3M scrubby would work. In that application there’s little danger of the mineral spirits affecting the plastic a lot. I just wouldn’t soak it in it.

No one listens to me anymore :stuck_out_tongue: Use Germ-X or Purel hand sanitizer, the alcohol concentration in both will remove the acrylic paint without damaging the plastic.

Soak it or rub it on.

You are correct if it’s acrylic. It didn’t sound like it was from his description, but worth a try.

Ill go check my paint.

These are them, the black and the clear coat. I can get better pictures :).

http://i1296.photobucket.com/albums/ag2/Bcmaddog/3A43FD01-43DF-490E-8AD2-1D4D586CE7B8-8723-0000058ED2FF1096_zps88049bfc.jpghttp://i1296.photobucket.com/albums/ag2/Bcmaddog/DFCE82BC-F1C7-407F-BE6B-5508121A3E5C-8723-0000058EC4385CB3_zpsff92d5c7.jpg

Yea, hand sanitizer won’t work against those, best bet is acetone, but that stuff will eat your plastic like it’s a strip of bacon.

http://i1296.photobucket.com/albums/ag2/Bcmaddog/65BDF497-53D0-4C2A-B6F2-8000F4ADFD68-8805-000005ABBC880C17_zpsde7f4e3b.jpghttp://i1296.photobucket.com/albums/ag2/Bcmaddog/E5BF79A2-F6AC-45FA-8443-FB8458F15962-8805-000005ABC05242BD_zpsee3b4ee3.jpg

Don’t ask. rubs neck

Then what’s the point if telling me that? :stuck_out_tongue:

Going to try the PGM by hand :/.

A time laps. http://i1296.photobucket.com/albums/ag2/Bcmaddog/IMG_0340_zps5d0ac0da.jpg
http://i1296.photobucket.com/albums/ag2/Bcmaddog/66D3BB49-77C9-4142-B27D-2DB4D7D3AD65-9476-00000610132171E2_zps49bdbb9b.jpghttp://i1296.photobucket.com/albums/ag2/Bcmaddog/6B922C0D-4FC9-452E-B57C-96BDC310C32A-9476-000006101922E0F5_zps42b88844.jpghttp://i1296.photobucket.com/albums/ag2/Bcmaddog/80644BF6-BD43-4C29-8737-D337E9EB14BF-9476-000006101C8F8659_zps5ad3b99c.jpghttp://i1296.photobucket.com/albums/ag2/Bcmaddog/D5488805-06DA-4EF5-A47C-F75E1507A371-9476-0000060FFC956227_zps45280d4c.jpghttp://i1296.photobucket.com/albums/ag2/Bcmaddog/A96CBCEE-095A-4808-BBB3-933F5C2A107C-9476-0000061007F379E2_zpse47c0a36.jpg